Tender For corrigendum : : supply, installation, testing & commissioning of electrical equipment for dg block 119a of inrp - ht panels (119a)supply, installation, testing & commissioning of indoor type floor mounted, single front, metal clad, 1250 a, 6.6 kv, 3 phase, 3 wire, vcb switchgear panel suitable for a short circuit current of 31.5 ka for 3 seconds, internally arc tested for 31.5 ka for 1 second, comprising of following incoming & outgoing feeders : incoming feeder: 1 no. 1250 a, 3p vcb outgoing feeders: i) 7 nos. 630 a, 3p vcbii) 1 no. 1250 a, 3p vcb as tie feederwith surge arrestors, relays, pts, cts & other necessary accessories including associated structural steel required for complete installation of the panel & equipment earthing of the panel from both the earthing terminals of the panel to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings. reference drg. nos: ip1/119a/05027339/dwg/001/r0 & ip1/119a/05027339/dwg/002/r0(note: terminal box of each incomer of 6.6kv switchboard shall be suitable for terminating 4x3cx400 sq.mm., 6.35/11kv (e), a2xwy cables.), supply of spares for ht panels as per attached spares list mentiond in section c, part ii of tender, 2.5 mva, 6.6/0.433 kv dry type transformers (119a)supply, installation, testing & commissioning of 6.6/0.433 kv, 2.5 mva, dyn11 dry type cast resin transformer having percentage impedance of 8.5% complete with ht cable end box, lt bus duct flange, off load tap changer on ht side with range of +/-5% in steps of 2.5%, wti scanner, ct for restricted earth fault protection and other necessary accessories including associated structural steel required for complete installation of the transformer & equipment & neutral earthing of the transformer from both the earthing terminals of the transformer to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & drawings.reference drg. no. : ip1/119a/05034347/dwg/001/r0, supply of spares for dry type transformers as per attached spares list mentiond in section c, part ii of tender, 2000 kva diesel generator sets (119a)supply, installation, testing & commissioning of 3 phase 2000 kva prime power 433v, 50hz, 0.8 p.f. diesel-generator sets with 110% overload capacity for 1 hr with four (4) stroke inline or vee type cylinder arrangement having engine speed 1500 rpm, 24v electric battery starting system with a provision of interchangeability of battery bank between two dg sets, complete with all auxiliary equipment including amf control panel, auxiliary mcc panels, heat exchanger cooling system, raw water pump, remote radiator with fans on terrace, ms exhaust piping, exhaust structure (maximum 30 m stack), 4 nos. of 3.6 cubic metre fuel day tank outside dg building (for all 4 dg sets) & 1 no. of 990 ltr intermittent tank inside each dg room, ms "c" class fuel piping between engine & fuel tank, dg room accoustic treatment & complete ventilation of dg room, brushless excitation for alternator, one no. 3200 amp 415 v 4p acb, ms structural steel supports/ channels/ angles & other necessary accessories including associated structural steel required for complete installation of the dg & equipment & neutral earthing of the dg from both the earthing terminals of the dg to the nearest earthing grid conductor existing at site using copper conductors of size as per tender technical specifications & necessary statutory clearances from cpcb etc. as required and as per tender technical specifications & drawings. design and construction of foundation for exhaust pipe rack/ structure of dg set is included in the scope of the contractor.reference drg. nos. : i) ip1/119a/05034347/dwg/001/r0ii) ip1/119a/05044831/dwg/003/r0iii) ip1/119a/05044831/dwg/004/r0iv) ip1/119a/05044831/dwg/005/r0v) ip1/119a/05044831/dwg/006/r0, supply of sp
Tender For supply of field kerosen supply scheme : : - 11 point 7 hp engine and high head water pump as per ts , puf tank 500 ltrs as per ts , spares tools oblique kit for each engine as per ts , high pressure pipe thermoplastic elastomer comma polyester yarn braided high pressure to conforming is code 12585 , tank connector , ball valves brass min 15mm , non return valve , pressure relief valve , by pass valve , suction stainer , 25 mm inner dia hdpe overflow and drain out pipe along with sockets of length 2 mtr for each tank , suction pipe 25 mm dia of length 3 and 4 mtr , hand operated rotary pump , hack saw blade of size 300 x 13 x 0 point 65 mm , closed grip heavy duty hand hack saw frame suitable for 300mm blades
Tender For supply of mt spares d d - v belt 1280 mm long , rubber hose radiator to thermostat , element oil filter , light extension inspection no 2 with 10 , box assy steering gear , joint assy axle shaft rh , bush stabliser mount , tool box , shoe set rear brake , cylinder assy rear wheel rh , cover assy , s a of fly wheel , wiper blades , cabin light , solenoid valve for diff lock alt , arm windshield wiper , distributor head , injector , reverse light , motor engine starter electrical , ram hydraulic ram assy , fuel shut off solenoid , alternator 28 55a 9515 631 , clutch booster vg 3284 , hydraulic jack 20t with lever , cover assy , assy mudflap rear , drive assy , assy release cable comp centre flap , drive shaft , tool bag , arm windshield wiper , assy wheel chock , assy sunvisor rh , speedo cable jis 4300 lg , assy motorised head lamp complete 24v rh , relay , roller ring assembly , rubber hose , hand priming pump , slave cyl clutch , spanner adjustable a 300 is 6149 g 2 , starter motor 12 volts , distributor head , repair kit major slave cylinder , assy fog lamp front yellow lens rh , rep kit air dryer assy , major kit clutch master cyl repair , vane pump , rubber hose radiator to engine , lamp 24v 21wd 24 1 t529201 , fuel water seprator , horn 24 v , repair kit minor clutch m cyl , horn 12 v , relay solenoid engine starter electrical , filter element , rep kit for wheel cyl , delivery hose 38mm x 30 mtr , tommy bar with square drive head for ope , bucket water canvas 6 , brake bleeding tube , hydraulic jack 12 ton with handle , tyre pressure gauge , tin box lamp filament , bulb for warning lamps ba 9s 24v , parking light bulb for head lamp 24v 4w , head lamp lh , head lamp rh
Tender For supply of rate contract for spares for parker make spares - pump (parker) part no.-t6c0103r03b1, 1/2" filter/regulator with mounting bracket part no.-p32ea14esabngp, 1/4" filter/regulator with mounting bracket part no.-p31ea12ebbngp, accumulator part no.-a4em0218l670h , accumulator part no.-a6em0578, air breather 3 micrometer rating, part no.-h00834004, b.c. ret. filter part no.-933117q, bowl real service kit part no.-rk22137 5540611800, brake pre. filter part no.-932630q, bucket control valve, part no.-1110.2204-012, ser 222104, bucket control valve, part no.-1110.2204-012, ser-000000189803, chain reel motor, part no.-30391106.40, sery1010-07096, chain reel motor, part no.-312.9218.042, se n1010-03823, charge pump part no.-5541-7432-00/0301359/ ser no. x111544322 parker-0301359, check valve part no.-d4a040 / nmk2, coil part no.- s8ld, coil (24vdc/20w) for the above part no.-s10ld , coil 24v dc part no.-20w, coil, solenoid, 24v part no.-851025, coolant filter element (recharge) part no.-5540524000/2350789/bw5140, cushion valve pre range 2000-2599 psi part no.-915a000045034 dwv-75-a-2500, directional valve part no.-e2b040z215nmk31516, dump lever, max psi 500 part no.-hc-379, dump line pre. reducing valve part no.-prh081s10-6t1138, b08-3-6t, engine oil filter element part no.- b9601 , f/w separator part no.-r60p, filter part no.-32630q 3000 23 wr, flow control valve, part no.-fs800s, 699052138293, fuel filter element part no.- bf900 , fuel water separator element, r90p part no.-, fuel water separator for lpdt ejc30s & pc th205l part no.-r-120t, high pressure filter element part no.-170z 222a, hyd. motor (compr.) part no.-3349212097, hyd. perc. (return) filter element part no.-937112q , hyd. pump part no.-3239110389, hyd. pump part no.-3239529166, hyd. pump part no.-3349122281, hyd. pump part no.-3349122265, hyd. pump part no.-3782009, hyd. pump part no.-324 9110 457, hyd. pump part no.-3129310176, hyd. pump part no.-t6cc-014-005-1r00-c1-00 , hyd. pump (brake) part no.-3129112553, hyd. pump (carrier) part no.-3269120007, hyd. pump (rot.) part no.-7029530011, hyd. pump (rotation) part no.-3339111656, hyd. pump (strg.) part no.-3129622160, hyd. pump (strg./d & h) part no.-3239120227, hyd. pump (tandem) part no.-3249120258, hyd. return filter part no.-1-c1096/11-524, hyd. return filter part no.-pr4467, hyd. return filter part no.-ucr6131, hyd. return filter part no.-fc1096/ff524, hyd. suc. filter part no.-921166, hydraulic filter element part no.-g01315q , hydraulic filter element part no.-925520, hydraulic filter element part no.-935145, hydraulic motor, part no.-3217903420/3349219084, hydraulic oil filter part no.-0060d010bn4hc 1250487m, hydraulic pump (rot., b/rb 281) part no.-3249529007, hydraulic pump (strg. & dump/hoist) part no.-3129612019, kit seal part no.-9121669650, kit seal part no.-9121591350, kit seal part no.-9120099014, kit, repair for relief valve (h1-05-12mp) part no.-h1 kit, kit, seal part no.-3217983409/3469149201 , kit, seal for the above, service kit, f300-26 part no.-3911802119, kit, seal, direction valve section part no.-398000k801, load control valve part no.-e2a060z-20-241, lp element, part no.-937967, sf1-r-40, lever (hand) part no.-6760382, motor (hose drum) part no.-3782009, o ring service kit no. 3 , o ring service kit no. 4 , o ring service kit no. 5 , o ring service kit no. 6 , o ring service kit no. 7 , o ring service kit no. 8 , overcenter valve part no.-e2b040z300nmk3, overcenter valve part no.- e2b040znmk3, pre relief valve part no.-rdh103510 mexico 1223, pre. accumulator ade075-21r9a2 v075l ps 210 bar t8-30/80 deg. c075-7315-028-641 , pre. red/relieving valve part no.-prn101510 mexico 1230, pressure switch, part no.-psb040af1a5x811, pump part no.-3217955410, pump (brake & str) part no.-3269120007, pump (brake) part no.-3129620173, pump (dump & hoist) part no.-3129320258, pump (dump & str) part no.-3039122108, pump (hyd.) part no.-3249115 023 , pump, part no.-5561847200, pu
Tender For supply of 11 point 7 hp engine and high head water pump as per ts , spares tools oblique kit for each engine as per ts , puf tank 500 ltrs as per relevant is , high pressure pipe thermoplastic elastomer comma polyester yarn braided high pressure to conforming is code 12585 , tank connector , ball valves brass min 15mm , non return valve , pressure relief valve , by pass valve , suction stainer , 25 mm inner dia hdpe overflow and drain out pipe along with sockets of length 2 mtr for each tank , suction pipe 25 mm dia of length 3 and 4 mtr , hack saw blade of size 300 x 13 x 0 point 65 mm , closed grip heavy duty hand hack saw frame suitable for 300mm blades
Tender For supply of establishment of watermanship training centre including electrrical engineer equipment - 1.1. modular construction, easy/ fast installation/ anti-skid surface/ uv protected/ more stable/ excellent buoyancy. 1.2. dimensions-8ft x 6.5ft x 1.5ft (length x width x height). 1.3. buoyancy-1000 kg. 1.4. railings- ms railings epoxy coated with nut and bolts. 2.1 hand held fire extinguisher (2 nos). 2.2. obm 90 hp suzuki outboard motor with accessories (fuel tank, steering remote system propeller, toolkit) & manufacture recommended list of spares (mrls). 3.1. dimensions-4.7m x 2.1m x 0.50m (length x width x buoyancy dia), 05 x chambers and 08 x person capacity. 3.2. hull construction fiberglass, u.v. resistance gelcoat, epoxy resin with vacuum infusion system and sandwich core material. 3.3. engine-90hp 4 stroke remote control engine with steering system. 3.4. accessories - pair of oars, foot pump (electric & manual), repair kit. 4.1. open covered mechanical storage shed (30 ft x 40 ft x 15ft). 4.2. profile sheet 40x30, iron pipe 3x3 inch, parlin 2x2 inch, brick wall 100ftx36inch and 08 x tube light. 5.1. rcc ramp 4m wide x 12m long, rcc pilar 12x12 inch, steell rat 18mm and 12mm. 5.2. reinforced concrete (m25) with non-slip finish. 5.3. ramp rcc thickness 6 inch
Tender For supply of spares of desl engine - filter as-lu, part no. 1r1808, filter as fu, part no. 1r0749, pri fuel filter, part no. 81531064, filter-air, part no. 4n0015, alternator g, part no. 6t1395, socket-connector, part no.8t8730, plug kit-con, part no. 1552260, switch, part no. 1083190, plug kit-con, part no. 1552274, socket-conne, part no. 8t8730, tachometer-e, part no. 1977348, vee belt, part no. 4n8216, ammeter, part no. 8m7892, solenoid as, part no. 1255774, vee belt set, part no. 4n6373, vee belt, part no. 4n8220, pump gp-wate, part no. 6057479, with lcc governor
Tender For procurement of cleaning materials for huskuru gp for the year 2026-27 - coco broom with 5 feet length only natural product to sweep the outdoor only, garbage cover small size, metal type big web stick16 to 24 feet length, small web stick 8 feet, metal dust pan, plastic dust pan, water jug normal size, plastic bucket, system herbicide glyphosate 41% sl, ammonium salt of glyphosate 71 % sg powder, grass cutter or weed cutter 4 stroke engine honda or other brand made company only 1 year motor warranty only without spares running petrol only, grass cutter or weed cutter 2 stroke engine with weed cutter 250meter wire 2sets of blades 1 year service warranty period without spares only china make only no brand petrol and oil running, with push cart set and 3phase honda motor and pump 100 meter flexible hose cable 2no spray guns 250 ltr capacity tank 1 year warranty for motor out of service is free up to 1year spare are chargeable, battery & manual sprayer to wear the back side 16ltr capacity tank no warrant for battery only service warranty 6months without spares only , giantbigfogging machine 1.9 ltr consumption ltr per hr chemical tank 5ltr capacity hand pump 3 to 4 time then cahrgeble battery running 1 year service warranty only with spares and labour charge are extra. to diesel and petrol running only, mini small fogging machine to spray for mesquites no warranty product to use diesel and mini gas can, the composition of malathion tech 5.0% based on 95% chain clay 10% soapstone, toilet cake or odonil fragrance of wash room purpose only, bamboo ladder, mop small cloth to use office table and chairs cleaning purpose only, clip mop set it use moping purpose to office only, apron, sodium hypo chloride, weed control chemical, mask branded, gum boots branded, pvc hand gloves 16 inches, coco broom, soft broom, toilet cleaning acid, malathion oil 5.0% e.c, pesticide (fogging chemical with water mix), fogging chemical (with fuel mix), black phenyl, white scented phenyl, alum crystal, malathion dust 5.0%e.c, bleaching powder 33% chlorine, safety helmets, sanitizer